Sieve analysis lab report

Therefore, sieving results are reproducible and precise an important precondition for a significant analysis.

A dense gradation will result in an even curve on the gradation graph. With careful selection of the gradation, it is possible to achieve high bulk density, high physical stability, and low permeability. But there are some applications which can only be carried out by wet sieving.

The vertical throwing motion is overlaid with a slight circular motion which results in distribution of the sample amount over the whole sieving surface. With an open gradation, the bulk density is relatively low, due to the lack of fine particles, the physical stability is moderate, and the permeability is quite high.

This results in many air voids, because there are no fine particles to fill them. These motional processes are characteristic of hand sieving and produce a higher degree of sieving for denser particles e.

Adjustment of parameters like amplitude and sieving time serves to optimize the sieving for different types Sieve analysis lab report material.

However, for material that is finer than mesh, dry sieving can be significantly less accurate.

Please help improve this section by adding citations to reliable sources. Limitations of sieve analysis[ edit ] This section does not cite any sources. May Learn how and when to remove this template message Most sieve analyses are carried out dry.

Wet sieve analysis can be utilized where the material analyzed is not affected by the liquid - except to disperse it. By having a dense gradation, most of the air voids between the material are filled with particles.

The rotating motion while suspended increases the probability that the particles present a different orientation to the mesh when they fall back again, and thus might eventually pass through the mesh. With a rich gradation, the bulk density will also be low, the physical stability is low, and the permeability is also low.

Throw-action[ edit ] Here a throwing motion acts on the sample. Types of gradation[ edit ] A Dense gradation A dense gradation refers to a sample that is approximately of equal amounts of various sizes of aggregate.

Sieve analysis assumes that all particle will be round spherical or nearly so and will pass through the square openings when the particle diameter is less than the size of the square opening in the screen.

Properties[ edit ] Gradation affects many properties of an aggregate. In the air they carry out free rotations and interact with the openings in the mesh of the sieve when they fall back. Horizontal sieve shakers are preferably used for needle-shaped, flat, long or fibrous samples, as their horizontal orientation means that only a few disoriented particles enter the mesh and the sieve is not blocked so quickly.

Amplitude and sieving time are set digitally and are continuously observed by an integrated control-unit. The reason for the effectiveness of this sieving method is based on two components: If the particles are smaller than the openings, they pass through the sieve.

May Learn how and when to remove this template message Sieve analysis has, in general, been used for decades to monitor material quality based on particle size.1 SIEVE ANALYSIS OF FINE AND COARSE AGGREGATES AASHTO T 27 SCOPE The sieve analysis, commonly known as the gradation test, is a basic essential test for all.

Sieve analysis

Related Documents: Sieve Analysis Test Lab Report Essay lab report Essay ANATOMY & PHYSIOLOGY CLASS: WRITING LAB REPORTS The following is an explanation of the format that is to be used for writing lab reports. Sieve analysis is a method used to determine the grain – size distribution of soils.

Mechanical Sieves/ Sieves is a device used for separating wanted elements from unwanted material or for characterizing the particle size distribution of 5/5(13). Sieve analysis test report 2. OBJECTIVE: To determine a particular soil grain size distribution(GSD) THEORY: The experiment is carried out to determine a good distribution of aggregate by using sieve and comparing the result obtained with BS SIEVE ANALYSIS OF FINE AND COARSE AGGREGATE TxDOT Designation: TexA Effective Date: August 1.

SCOPE Perform the sieve analysis immediately after removing the sample from the oven. 5. PROCEDURE Report the cumulative percent retained on each sieve to the nearest whole percent. A sieve analysis (or gradation test) is a practice or procedure used (commonly used in civil engineering) to assess the particle size distribution.

Download
Sieve analysis lab report
Rated 4/5 based on 71 review